 |
PULSE AUTOCYCLE NETWORK 
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in| Search found 9 matches |
| Author | Message |
|---|---|
 Topic: New Pulse Owners |
|
| DON SUCHA Replies: 4 Views: 6075 |
 Forum: The Forum Posted: Sat Dec 23, 2006 9:00 am Subject: Pulse Cooling and Electric System |
| Erik: The electrical system on the Yamaha 400 powered Pulse is marginal but can be made workable by keeping the current load to a minimum. The wires are too small going from the battery foreward ... | |
| Topic: Engine Cooling |
|
| DON SUCHA Replies: 13 Views: 16205 |
Forum: The Forum Posted: Mon Jan 16, 2006 7:59 pm Subject: Engine Cooling |
| The Mobil Synthetic V Twin oil does not run much cooler than regular oil as far as I can tell. The reason I use it is that it does not break down with high heat. It lubricates under extreme temperatur ... | |
| Topic: On Board Compressor for Rear Air Shocks |
|
| DON SUCHA Replies: 7 Views: 8667 |
Forum: The Forum Posted: Wed Oct 05, 2005 3:16 am Subject: On Board Compressor for Rear Air Shocks |
| Pulse 246 has front and rear air shocks. I installed an AIR LIFT Load Controller II compressor, AIR LIFT part # 25812. This system has 1 compressor, two pressure guages, two bleed valves and two ... | |
| Topic: OVERHEATING-Remote oil cooler |
|
| DON SUCHA Replies: 8 Views: 8117 |
Forum: The Forum Posted: Sat Aug 20, 2005 10:57 am Subject: Oil cooler and fans |
| Scott: The lower air scoop is made of fiberglass and attached to the original mounting holes. The cylinder cooling fans are supplied air from the left NACA air inlet and the lower air scoop. The or ... | |
| Topic: OVERHEATING-Remote oil cooler |
|
| DON SUCHA Replies: 8 Views: 8117 |
Forum: The Forum Posted: Thu Aug 18, 2005 12:58 am Subject: Oil cooler adapter for Yamaha 400 |
| I had an oil cooler adapter made to the specs which I am posting on
www.clarksonmotor.com/gallery/pulse To see the oil cooler adapter blueprints go to the pulse modifications gallery, page 3, Do ... |
|
| Topic: Engine Cooling |
|
| DON SUCHA Replies: 13 Views: 16205 |
Forum: The Forum Posted: Sun Jul 25, 2004 1:26 am Subject: engine cooling |
| Nelson
I did not repaint the engine. Pulse #256 was never sold retail and did not have many miles when I got it. The original dealer had it for most of it's life so perhaps he did not overheat it ... |
|
| Topic: Engine Cooling |
|
| DON SUCHA Replies: 13 Views: 16205 |
Forum: The Forum Posted: Thu Jul 22, 2004 7:47 am Subject: engine cooling |
| Steve
The engine temperatures were from the original Pulse guages. The oil cooler sensor is the engine drain plug and seems accurate since the oil cooler fan turns on when the Pulse guage shows abou ... |
|
| Topic: Engine Cooling |
|
| DON SUCHA Replies: 13 Views: 16205 |
Forum: The Forum Posted: Wed Jul 21, 2004 10:14 am Subject: engine cooling |
| Pulse #246 does not have A/C. Pictures of cooling system modifications can be seen at http://www.clarksonmotor.com/gallery/pulse I will add pictures of the lower duct from the air scoop to cooling ... | |
| Topic: Engine Cooling |
|
| DON SUCHA Replies: 13 Views: 16205 |
Forum: The Forum Posted: Tue Jul 20, 2004 5:35 am Subject: Engine Cooling |
| Pulse #246 with Yamaha 400 engine and engine cooling modifications. To improve engine cooling I installed 2 - 8" cooling fans [thermostatically controlled on at 240 degrees] directly in front of th ... | |
All times are GMT + 6 Hours |
Powered by phpBB 2.0.22-1 (Debian) © 2001, 2005 phpBB Group